6 x 10.25 x .125 Heat Conductive Green Rubber Pad

Videos

No videos for this product

Client Gallery

Product Instructions

Quick Summary - Click the button below for the full instructions with videos and stacking order.

Time: 0 seconds
Temperature: N/A°F (-18°C)
Pressure: Light

Heat Press Instructions:
Green Heat Conductive Rubber Pads

Heat conductive rubber pads are used to provide even heat to surfaces that might not be perfectly flat. It is our recommendation for imaging porcelain, stone and glass tile, glass cutting boards, and porcelain ornaments. Green silicon rubber pads are most commonly used in pressing to porcelain and glass.

We offer these pads in two thicknesses for dye sublimation imprinting:
~ The 1/16"(.0625") thickness is recommended for jewelry and porcelain ornaments. HCR-16
~ 1/8" (.125") is perfect for glass cutting boards, tiles and plaques. HCR-18

Heat conductive rubber, also referred to as green heat conductive rubber, is a unique closed cell silicone sponge that has very fine ceramic particles mixed in the polymer to enhance its thermal properties. This expanded, conductive rubber helps distribute pressure and protect delicate materials in the heat press. Heat conductive rubber press pad material is visually identified by its light green color and fine fabric finish.

The 1” Linear Yards are cut to fit your specifications.
You order it in any width you want and it would be 36" (or 60") long.
HCR-16-1.................. 1” x 36” x .0625”, Linear Yard
HCR-18-1.................. 1” x 36” x .125”, Linear Yard
HCR-19-1.................. 1” x 60” x .125”
RBR-16-1.................. 1” x 36” x .0625”, Linear Yard, Red for replacement for dyewraps

These pads were created for specifc uses:
HCR-1855.................. 5” x 5” x .125” is recommended for 4x4 Tiles
HCR-1877.................. 7” x 7” x .0625” is recommended for 6x6 Tiles
HCR-1677.................. 7” x 7” x .0625” is recommended for Porcelain Plates
HCR-18610.................. 6” x 10.25” x .125” is recommended for Stainless Water Bottles
HCR-1868.................. 6” x 8” x .125” is recommended for 6x8 Tiles
HCR-1847.................. 4” x 7” x .125” is recommended for 3” x 6” Tiles


Our green rubber is of very good quality and should last through many pressings.

~ On every occasion, cover your green rubber with protective paper to keep it from being stained by your sublimation ink.

~ If you do find it stained with ink, cover the inky area with protective paper and put it under the press for 10+ minutes and it should come off onto the paper.

~ Normal dust or dirt from being dropped on the floor can be cleaned from the green pad with a mild detergent. Avoid leaving it in water or wet. Also do not leave it in direct heat or sunlight. A cool dry place is the best storage area.

........................................................................................

DK3 Heater GREEN PAD replacement instructions
Use HCR-18510 and
1. Scrape off all green rubber carefully: do not cut the temperature sensor wire under the green
pad at the bottom.
2. Removing all adhesive is not necessary: basic smoothness is all we need. Do not remove the
band heater from the frame either - not necessary and won't help.
3. Apply high temp silicone adhesive to one entire side of pad. We recommend FAC-SILC3.
4. Stick pad onto band heater. Put 2 mugs into the press back to back and clamp the press
locked shut with EXTREMELY LIGHT PRESSURE, so the green pad is held in place evenly,
but the adhesive is not overly squeezed out.
5. Let it cure/dry overnight.


Additional Items Needed: Green Pad
Recommended Paper: N/A

Blog Posts

Reviews

WHAT OUR CUSTOMERS SAY

This stuff is fantastic for sublimating water bottles in my mug heat press! I just open the mug heat press and turn the water bottle completely around half way through the heat cycle and get perfect design all around the bottle. I was skeptical but it was worth the money!
Angie in NM

Write review this product!
Complete this form below and you'll be entered into our weekly prize draw to win a $25 Conde Account Credit! A lucky winner will be drawn randomly on Friday of each week and notified by email.

Your name

Your email (not displayed publicly)

Your review

Captcha   

Submit

Product Support

Downloads

Suggested Retail Price Range

To view the suggested retail pricing for this item, log in.

Read: The Ultimate Guide to Retail Pricing Sublimation Products